Structure and Mechanical Stability of Epoxy Modified Polyurethane Foam Under Heat and Stress

A series of phenolic epoxy resin (PEP) modified polyurethane foams (PUF) were prepared via an in-situ polymerization, one step process. It was found that the epoxy modified PUF foam exhibited a perforated network structure with larger cell size, higher open cell porosity and enhanced ovality compared with pure PUF. With increasing content of PEP, the tensile strength, elongation at break and low temperature modulus of PUF decreased. A single T_g was observed for PEP modified PUF, indicating that the two component phases of the polyurethane-epoxy were miscible. With increasing PEP content, the T_g of PUF shifted slightly to higher temperature, tan δ_max dropped to lower values, and the retention value of the storage modulus at ?20 and ?10?°C increased. For pure PUF, the cell walls degraded and the structure became disordered after aging under heat and stress, while for PUF/20wt%PEP, the degradation degree was obviously reduced, and an orientation of the cells along the stress direction and a density increase was observed. During aging at 200?°C, the retention of the mechanical properties of PUF/20wt% PEP was much higher than that of pure PUF, and it showed superior stability under heat and stress, attributed to incorporation of the thermally resistant oxazolidone rings and benzene rings in the PU backbones, the highly cross-linked networks of the polyurethane-epoxy systems and the obvious orientation of the cells under stress.     

Binding and cytotoxicity of 131I-labeled gastrin-releasing peptide receptor antagonists modified by cell penetrating peptides

Gastrin releasing peptide receptors (GRPRs) are one of the most interesting targets over expressed in various tumors. Due to the superior potential of the GRPR antagonist analogs, they have been studied in the tumor radio imaging and therapy field. However, typical antagonists suffered the shortcomings of no internalization and poor binding affinity which hampered their applications in radiotherapy. Therefore, we attempted to introduce Oligoarginines (cell penetrating peptides) to RM26, aiming to increase the binding affinity or even trigger the internalization of the peptides on cells. The results showed Arg₆ as the most potent CPP, significantly enhanced the binding avidity of RM26 to the GRPR.

     

One-step synthesis of magnetic composite UiO-66/Fe3O4/GO for the removal of radioactive cesium ions

Journal of Radioanalytical and Nuclear Chemistry - In this study, the UiO-66/Fe3O4/GO composite was prepared by one step method for removal of cesium ions (Cs+) in water and exhibited excellent...     

Semiconducting Polymer Dots with Dual-Enhanced NIR-IIa Fluorescence for Through-Skull Mouse-Brain Imaging

Fluorescence probes in the NIR-IIa region show drastically improved imaging owing to the reduced photon scattering and autofluorescence in biological tissues. Now, NIR-IIa polymer dots (Pdots) are developed with a dual fluorescence enhancement mechanism. First, the aggregation induced emission of phenothiazine was used to reduce the nonradiative decay pathways of the polymers in condensed states. Second, fluorescence quenching was minimized by different levels of steric hindrance to further boost the fluorescence. The resulting Pdots displayed a fluorescence QY of ca. 1.7 % in aqueous solution, suggesting an enhancement of ca. 21 times in comparison with the original polymer in tetrahydrofuran (THF) solution. Small-animal imaging by using the NIR-IIa Pdots exhibited a remarkable improvement in penetration depth and signal to background ratio, as confirmed by through-skull and through-scalp fluorescent imaging of the cerebral vasculature of live mice.     

纳米CeO2吸附剂的制备及对六价铬的吸附性能

吸附法是去除水中重金属离子的重要方法,开发新型吸附剂一直是研究热点.利用浸渍法和水热法制备了片状和无定形的纳米CeO2吸附剂,探讨其对六价铬的吸附性能,分析pH、吸附时间、六价铬初始浓度等因素对其吸附性能的影响,并通过循环吸附实验考察纳米CeO2吸附剂的再生能力.结果表明:厚度30 nm、直径大小约为400 nm的片状CeO2吸附剂具有更强的吸附能力和更快的吸附速率,80 min时基本达到吸附平衡;两种吸附剂的最佳吸附pH为3;吸附动力学均符合伪二级动力学方程,Langmuir模型和Freundlich模型均能很好地拟合等温吸附过程,表明纳米CeO2对六价铬的吸附以单层吸附为主.片状CeO2四次吸附-解吸实验之后吸附率稍有下降,表明片状CeO2吸附剂有较好的再生能力,因而,该片状CeO2吸附剂适用于与酸性Cr(Ⅵ)废水的处理.     

Force Chain Characteristics and Effects of a Dense Granular Flow System in a Third Body Interface During the Shear Dilatancy Process

In order to investigate the characteristics of force chains in a granular flow system, a parallel plate shear cell is constructed to simulate the shear movement of an infinite parallel plate and observe variations in relevant parameters. The shear dilatancy process is divided into three stages, namely, plastic strain, macroscopic failure, and granular recombination. The stickslip phenomenon is highly connected with the evolution of force chains during the shear dilatancy process. The load–distribution rate curves and patterns of the force chains are utilized to describe the load-carrying behaviors and morphologic changes of force chains separately. Force chains, namely, “diagonal gridding,” “tadpole-shaped,” and “pinnate” are defined according to the form of the force chains in the corresponding three stages.     

高雷诺数下非混相Rayleigh-Taylor不稳定性的格子Boltzmann方法模拟

本文采用相场格子Boltzmann方法研究了竖直微通道内中等Atwoods数流体的单模Rayleigh-Taylor不稳定性问题,系统分析了雷诺数对相界面动力学行为以及扰动在各发展阶段演化规律的影响.数值结果表明高雷诺数条件下,不稳定性界面扰动的增长经历了四个不同的发展阶段,包括线性增长阶段、饱和速度阶段、重加速阶段及混沌混合阶段.在线性增长阶段,我们计算获得的气泡与尖钉振幅符合线性稳定性理论,并且线性增长率随着雷诺数的增加而增大.在第二个阶段,我们观察到气泡与尖钉将以恒定的速度增长,获得的尖钉饱和速度略高于Goncharov经典势能模型的解析解[Phys.Rev.Lett.200288134502],这归因于系统中产生了多个尺度的旋涡,而涡之间的相互作用促进了尖钉的增长.随着横向速度和纵向速度的差异扩大,气泡和尖钉界面演化诱导产生的Kelvin–Helmholtz不稳定性逐渐增强,从而流体混合区域出现许多不同层次的涡结构,加速了气泡与尖钉振幅的演化速度,并在演化后期阶段,导致界面发生多层次卷起、剧烈变形、混沌破裂等行为,最终形成了非常复杂的拓扑结构.此外,我们还统计了演化后期气泡与尖钉的无量纲加速度,发现气泡和尖钉的振幅在后期呈现二次增长规律,其增长率系数分别为0.045与0.233.而在低雷诺条件下,重流体在不稳定性后期以尖钉的形式向下运动而轻流体以气泡的形式向上升起.在整个演化过程中,界面变得足够光滑,气泡与尖钉在后期的演化速度接近于常数,未观察到后期的重加速与混沌混合阶段.     

Experimental and Numerical Investigation on Effects of the Steam Ingestion on the Aerodynamic Stability of an Axial Compressor

In order to investigate the influence of steam ingestion on the aerodynamic stability of a two-stage low-speed axial-flow compressor, multiphase flow numerical simulation and experiment were carried out. The total pressure ratio and stall margin of the compressor was decreased under steam ingestion. When the compressor worked at 40% and 53% of the nominal speed, the stall margin decreased, respectively, by 1.5% and 6.3%. The ingested steam reduced the inlet Mach number and increased the thickness of the boundary layer on the suction surface of the blade. The low-speed region around the trailing edge of the blade was increased, and the flow separation region of the boundary layer on the suction surface of the blade was expanded; thus, the compressor was more likely to enter the stall state. The higher the rotational speed, the more significant the negative influence of steam ingestion on the compressor stall margin. The entropy and temperature of air were increased by steam. The heat transfer between steam and air was continuous in compressor passages. The entropy of the air in the later stage was higher than that in the first stage; consequently, the flow loss in the second stage was more serious. Under the combined action of steam ingestion and counter-rotating bulk swirl distortion, the compressor stability margin loss was more obvious. When the rotor speed was 40% and 53% of the nominal speed, the stall margin decreased by 6.3% and 12.64%, respectively.